JLG 534D-10 Features And Specs
JLG 534D-10 Features
The JLG 534D-10 telehandler combines high performance with durability for job sites demanding power and agility.
JLG 534D-10 Specs
| Rated Capacity at 24 in. (610 mm) load center | 10,000 lb (4,536 kg) |
| Maximum Lift Height | 45 ft (13.7 m) |
| Frame Leveling | 8 degrees |
| Lift Speed (boom retracted) | Up: 10.8 sec Down: 8.1 sec |
| Boom Speed | Extend: 14.5 sec Retract: 13.4 sec |
| Travel Speeds Forward | 2WD 0-19 mph (30.6 kmph) 4WD 0-6.5 mph (10.5 kmph) |
| Drawbar Pull (Loaded) | 21,000 lb (9,526 kg) |
| Operating Weight with 48 in. (1.2 m) carriage and forks | 25,300 lb (11,476 kg) |
| Length (less forks) | 237 in. (6.01 m) |
| Width | 98.8 in. (2.50 m) |
| Height | 93 in. (2.36 m) |
| Wheelbase | 135 in. (3.42 m) |
| Ground Clearance | 19.3 in. (490 mm) |
| Outside Turning Radius | 175 in. (4.44 m) |
| Max. Reach from Front Tires to 24 in. (610 mm) Load Center | 31.5 ft (9.60 m) |
STANDARD EQUIPMENT, OPTIONS & ATTACHMENTS FOR THE JLG 534D-10
Engine
- Make and Model John Deere 4045TF275
- Turbocharged
- Fuel No. 2 Diesel
- Cycles 4
- No. of Cylinders 4
- Displacement 276 cu in (4.5 L)
- Rated Speed 2,500 rpm
- Max. Gross BHP 115 hp (85 kW)
- Fuel Tank 38 gal (144 L)
Engine Filters
- Two-stage dry air cleaner — centrifugal pre-cleaner with continuous dust ejector plus replaceable dry filter element.
- Visual service indicator.
- Replaceable spin-on fuel filter.
- Full-flow replaceable spin-on engine oil filter.
Electrical System
- Voltage: 12V
- Alternator: 65 amp
- Battery: 1050 cold cranking amps at 0°F
Hydrostatic Drive
- 6,300 PSI (43,437 kPa) closed loop with piston pump and motors.
- All hydraulic connections ORS and Code 62 O-ring flanges.
- Integral reservoir with implement hydraulics.
- 8 micron suction filter for charge pump.
- Self-contained, swashplate design, variable displacement, over center, piston pump.
- Neutral start switch. (Park brake must also be engaged to start.)
- 2WD — 4WD inching.
- Audible back-up travel alarm mounted in counterweight area signals reverse movement.
Axles
- Planetary hubs with piston motors on rear axle.
- Piston motor-driven planetary front axle with high-bias differential.
Service Brakes
- Hydraulic wet disc brake on each front wheel.
- Hydraulic dynamic braking on front axle and both rear wheels.
Parking Brakes
- Wet disc spring-applied electro/hydraulic release, fail-safe on both front wheels.
- Light on dash indicates when brakes are on.
- Frame mounted right side rear view mirror.
Tires
- Standard: 14:00 x 24 — 12PR, G2 type.
- Optional: Radial 14:00 x 24 — 12PR L2 rock tires.
Cab
- Certified ROPS/FOPS structure with horn, back-up alarm and standard right side rear view mirror.
- Forward, neutral, reverse lever on left of steering column.
- Single foot pedal control provides both braking and inching for lifting while maneuvering vehicle.
- Electro/hydraulic traction lock valve for superior tractive effort.
Steering
- Hydraulic power steering with manual backup.
- Rear wheel steering, 90° pivot around either front tire.
- Outside turning radius is less than chassis length.
Instruments
- Volt meter, hourmeter, engine oil pressure, temperature, fuel gauge.
- All gauges protected by clear acrylic cover.
Controls
- Grouped for operator comfort and convenience.
- 2WD and 4WD switch on dash.
- Boom lift and crowd on single joystick.
- Right-hand tilt and sway lever.
- Foot throttle.
- Floor mounted traction lock switch.
Hydraulic System-Implement
- Single-section gear pump.
- 40 gal (151.6 L) system capacity.
- 8 micron filter with visual service indicator and suction strainer.
- Lift, crowd, tilt and sway cylinders have safety checks to prevent dropping of load in the event of hose or other hydraulic failure.
Auxiliary Hydraulics
- Used for all attachments equipped with cylinders or other hydraulic components.
- Consists of valves, controls and hydraulic lines.
- Cab Enclosure Lockable, split door.
- Windshield wiper.
- Heater & defroster fan.
- Light Group Consists of 2 cab-mounted headlights, 1 backup/tail/stoplight and rotating beacon.
- Radial and Rock Tires Winch Left Hand Tilt/Sway Control Tilt on Joystick
- Standard Carriage 48 in. (1.2 m), 66 in. (1.7 m) or 72 in. (1.8 m)
- Side Tilt Carriage 48 in. (1.2 m) or 66 in. (1.7 m)
- 100° Swing Carriage 72 in. (1.8 m) Carriage
- 180° Swing Carriage 72 in. (1.8 m)
- 100° Drywall Swing Carriage 72 in. (1.8 m)
- Pallet Forks 2 x 6 x 48 in. (51 mm x 152 mm x 1.2 m)
- Cubing Forks 2 x 2 x 48 in. (51 mm x 51 mm x 1.2 m)
- Vertical Mast 6 ft (1.8 m)
- 100° Swing Mast 6 ft (1.8 m)
- Truss Boom With or Without Winch 10 ft (3.0 m)
- Bucket 0.75 cu yd (0.57 m3 ) or 1.25 cu yd (0.95 m3)
- Work Platform
- Slip On Crane Hook
- Instant Hook
Interested in buying the JLG 534D-10? Contact MJ Equipment today!